Wiring Tools


These tiny bits are helpful aids for installing any of the various Cir-Kit Concepts' wiring and lighting fixtures. Their use greatly enhances and simplifies installation in all types of wood. The No. 55 bit is used in making starter holes for the CK801 eyelets and for the small hollow eyelets used at tape run interconnect points. Measures .052" in diameter. (CKC1025-4)

These tiny bits are helpful aids for installing any of the various Cir-Kit Concepts' wiring and lighting fixtures. Their use greatly enhances and simplifies installation in all types of wood. The No. 70 bit may be used in place of a push pin for making .028" holes in copper tape runs This size hole allows easy bradding of either a 12-volt GOW or wire terminal bulb into a conductive tape run. All bits may be used with either a 1/4" electric drill or the CK201 Mini Drill. (CKC1025)

These tiny bits are helpful aids for installing any of the various Cir-Kit Concepts' wiring and lighting fixtures. Their use greatly enhances and simplifies installation in all types of wood. The No. 75 bit allows drilling of small .021" holes at tape juncture points for easy insertion of 1/8" brads in hardwood or Masonite structures. (May also be used for outlet and switch nails.) The drilling of holes simplifies brad installation and assures a tight electrical fit between the brad and copper strip. All bits may be used with either a 1/4" electric drill or the CK201 Mini Drill. (CKC1025-1)

These tiny bits are helpful aids for installing any of the various Cir-Kit Concepts' wiring and lighting fixtures. Their use greatly enhances and simplifies installation in all types of wood. The 1/32" bit provides the proper size hole for wall sconce wires. This hole allows the pulling of sconce wires through a wall and electrically connecting them into a conductive tape run on the opposite side of a wall. (The wires are inserted into copper strip holes made with either a push pin or No. 70 bit).

This wire is used wherever single, extremely small size conductors are required. The wire is an amazingly small .018" in diameter and may be easily stripped with the fingernails. The single conductor green wire is the same wire as that used on our Christmas light strings. Covered by a thin plastic insulation.

These curved tip forceps provide a significant advancement in the brass brad insertion process. Their locking handles and fine serrated teeth allow easy gripping and holding of 1/8" brass brads in even the most awkward locations. Made of surgical stainless steel these tools are ideal for home or shop workbench. Overall length 5". (CKC1046) By Cir-Kit Concepts.

These straight forceps provide a significant advancement in the brass brad insertion process. Their locking handles and fine serrated teeth allow easy gripping and holding of 1/8" brass brads in even the most awkward locations. Made of surgical stainless steel these tools are ideal for home or shop workbench. Overall length 5". (CKC1046-1)

Replacement pins for Cir-Kit Concepts Awl. For use with CK1044 awl. For use with dollhouse electrical installation.

Brad Insertion Simplified Over the years, the use of tapewire has become the predominat worldwide method of dollhouse wiring. Its versatility and ease of installation had made it the dollhouse electrician's method of choice. However, to achieve low-profile corners, it is necessary to use tiny 1/8" brass brads to create the necessary electrical interconnection. Although these brads serve this purpose very well, they can be frustrating to hold and install. That's where the new CKC1054 Brad Placement Tool comes in. With this tool the brad can be held firmly in place as it is inserted into the tape run. No more lost brads or blue language. They are manufactured of stainless steel with a plastic coated handle for a lifetime of operation. The CKC1054 should be a must for every tape wiring toolbox.  (CKC1054).

Brad Placement Tool by Cir-Kit Concepts.

The CK1041 hammer, as shown, has been specially designed and manufactured for Cir-Kit Concepts to aid and simplify the brass brad and eyelet installation process. Its size and weight allow easy use in even the most remote corners of a dollhouse. Only 5½" long, the hammer is made with a solid brass head and a deeply serrated steel handle for a positive grip. The weighted brass head makes it ideal for any number of miniature building projects!

These tiny bits are helpful aids for installing any of the various Cir-Kit Concepts' wiring and lighting fixtures. Their use greatly enhances and simplifies installation in all types of wood. The No. 55 bit is used in making starter holes for the CK801 eyelets and for the small hollow eyelets used at tape run interconnect points. Measures .052" in diameter. (CKC1025-4)

Categories

Top Seller

0 Item(s)
US$0.00